Jump Starting Battery on 2005 BMW 325?

When battery goes weak or dead, the car will not start.In that case the jump starting the battery is required to start the car.
The details are as follows :---

Jump Starting A Dead Battery

Whenever a vehicle is jump started, precautions must be followed in order to prevent the possibility of personal injury. Remember that batteries contain a small amount of explosive hydrogen gas which is a by-product of battery charging. Sparks should always be avoided when working around batteries, especially when attaching jumper cables. To minimize the possibility of accidental sparks, follow the procedure carefully.

Fig. Connect the jumper cables to the batteries and engine in the order shown

WARNING

NEVER hook the batteries up in a series circuit or the entire electrical system will go up in smoke, including the starter!

Vehicles equipped with a diesel engine may utilize two 12 volt batteries. If so, the batteries are connected in a parallel circuit (positive terminal to positive terminal, negative terminal to negative terminal). Hooking the batteries up in parallel circuit increases battery cranking power (amperage) without increasing total battery voltage output. Output remains at 12 volts. On the other hand, hooking two 12 volt batteries up in a series circuit (positive terminal to negative terminal, positive terminal to negative terminal) increases total battery output to 24 volts (12 volts plus 12 volts).

E30 Models

1. Make sure that the voltages of the 2 batteries are the same. Most batteries and charging systems are of the 12 volt variety.
2. Pull the jumping vehicle (with the good battery) into a position so the jumper cables can reach the dead battery and that vehicle's engine. Make sure that the vehicles do NOT touch.
3. Place the transmissions of both vehicles in Neutral (MT) or P (AT), as applicable, then firmly set their parking brakes.

NOTE

If necessary for safety reasons, the hazard lights on both vehicles may be operated throughout the entire procedure without significantly increasing the difficulty of jumping the dead battery.

1. Turn all lights and accessories OFF on both vehicles. Make sure the ignition switches on both vehicles are turned to the OFF position.
2. Cover the battery cell caps with a rag, but do not cover the terminals.
3. Make sure the terminals on both batteries are clean and free of corrosion or proper electrical connection will be impeded. If necessary, clean the battery terminals before proceeding.
4. Identify the positive (+) and negative (-) terminals on both batteries.
5. Connect the first jumper cable to the positive (+) terminal of the dead battery, then connect the other end of that cable to the positive (+) terminal of the booster (good) battery.
6. Connect one end of the other jumper cable to the negative (-) terminal on the booster battery and the final cable clamp to an engine bolt head, alternator bracket or other solid, metallic point on the engine with the dead battery. Try to pick a ground on the engine that is positioned away from the battery in order to minimize the possibility of the 2 clamps touching should one loosen during the procedure. DO NOT connect this clamp to the negative (-) terminal of the bad battery.

CAUTION

Be very careful to keep the jumper cables away from moving parts (cooling fan, belts, etc.) on both engines.

1. Check to make sure that the cables are routed away from any moving parts, then start the donor vehicle's engine. Run the engine at moderate speed for several minutes to allow the dead battery a chance to receive some initial charge.
2. With the donor vehicle's engine still running slightly above idle, try to start the vehicle with the dead battery. Crank the engine for no more than 10 seconds at a time and let the starter cool for at least 20 seconds between tries. If the vehicle does not start in 3 tries, it is likely that something else is also wrong or that the battery needs additional time to charge.
3. Once the vehicle is started, allow it to run at idle for a few seconds to make sure that it is operating properly.
4. Turn ON the headlights, heater blower and, if equipped, the rear defroster of both vehicles in order to reduce the severity of voltage spikes and subsequent risk of damage to the vehicles' electrical systems when the cables are disconnected. This step is especially important to any vehicle equipped with computer control modules.
5. Carefully disconnect the cables in the reverse order of connection. Start with the negative cable that is attached to the engine ground, then the negative cable on the donor battery. Disconnect the positive cable from the donor battery and finally, disconnect the positive cable from the formerly dead battery. Be careful when disconnecting the cables from the positive terminals not to allow the alligator clips to touch any metal on either vehicle or a short and sparks will occur.

E36 Models

Fig. The remote positive battery terminal is used for jump starting

Fig. Open the hood and lift up the protective cover to expose the jump post for the positive (+) lead of the jumper cable

Fig. Attach the jumper cable's negative (-) lead to the negative (-) jump post, and the positive (+) lead to the positive (+) jump post

BMW provides a positive and negative jump start post in the engine compartment on the passenger's side. The positive jump start post is located underneath a protective plastic cover with a large + symbol cast into the cover. To jump start the vehicle using the under hood battery posts proceed as follows:

1. Verify that the vehicle used to supply battery voltage has a 12 Volt system with a similar sized battery, and correctly identify the positive and negative battery terminals.
2. Pull the jumping vehicle (with the good battery) into a position so the jumper cables can reach the dead battery and that vehicle's engine. Make sure that the vehicles do NOT touch.
3. Place the transmissions of both vehicles in Neutral (MT) or P (AT), as applicable, then firmly set their parking brakes.

NOTE

If necessary for safety reasons, the hazard lights on both vehicles may be operated throughout the entire procedure without significantly increasing the difficulty of jumping the dead battery.

1. Properly connect the positive battery jumper cable lead to the vehicle used to supply the required voltage. The red lead of the jumper cable is the positive battery lead.
2. Lift up the positive jump post protective cover on the vehicle to be jumped and attach the positive lead of the jumper cable.
3. Locate the large hex shaped negative grounding lug on the shock tower or firewall on the vehicle to be jumped, and attach the negative lead (black) of the jumper cables to the grounding lug.

CAUTION

Be very careful to keep the jumper cables away from moving parts (cooling fan, belts, etc.) on both engines.

1. Connect the negative lead to the supply vehicle's battery ground, or to a suitable chassis or engine ground. DO NOT allow the jumper cable leads to touch one another at any time.
2. Once the vehicle has been started, turn on the headlights and set the climate control blower to the highest speed for at least 10 seconds before disconnecting the battery jumper cables to avoid a voltage spike at the voltage regulator.
3. Carefully disconnect the cables in the reverse order of connection. Start with the negative cable that is attached to the engine ground, then the negative cable on the donor battery. Disconnect the positive cable from the donor battery and finally, disconnect the positive cable from the formerly dead battery. Be careful when disconnecting the cables from the positive terminals not to allow the alligator clips to touch any metal on either vehicle or a short and sparks will occur.

Jump Starting Precautions

Be sure that both batteries are of the same voltage. Most vehicles on the road today use a 12-volt charging system.

Be sure that both batteries are of the same polarity (have the same terminal, in most cases NEGATIVE grounded).

Be sure that the vehicles are not touching or a short could occur.

On serviceable batteries, be sure the vent cap holes are not obstructed.

Do not smoke or allow sparks anywhere near the batteries.

In cold weather, make sure the battery electrolyte is not frozen. This can occur more readily in a battery that has been in a state of discharge.

Do not allow electrolyte to contact your skin or clothing.

---------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

Car wont start?

http://howtobyme.blogspot.com/2011/10/car-wont-start.html

----------