How to remove clutch disc and pressure plate on 2005 BMW 325 ?

Driven Disc & Pressure Plate

CAUTION

The clutch disk contains asbestos, which causes some forms of lung disease and may be a cancer causing agent. Do not clean the clutch or housing with compressed air. Use a damp rag to wipe off surfaces and throw away the rag. Use commercial available brake cleaners if a solvent is necessary. Avoid inhaling any dust from the clutch surfaces.

NOTE

The clutch disk, pressure plate, release bearing and pilot bearing are considered normal wear items. If the clutch disk or pressure plate are worn/defective, all of these components should be replaced.

Removal & Installation

NOTE

Inspect the rear main/flywheel seal for leakage when accessing the clutch.

1. Remove the transmission as outlined in this section.
2. Place a suitable drain pan under the clutch assembly.

CAUTION

Eye protection should be worn at all times. The use of a protective breathing mask is recommended. Use care, and do not allow exposed skin to come in contact with cleaning solvents or clutch dust.

1. Clean the clutch assembly with an approved brake cleaning fluid.
2. Lock the flywheel in place using a suitable flywheel locking tool.
3. Insert, if available, a clutch alignment tool.
4. Matchmark the pressure plate to the flywheel.
5. Remove the clutch pressure plate fasteners evenly using a crisscross pattern, then remove the clutch pressure plate. If a clutch alignment tool is not being used, remove the pressure plate slowly to prevent the clutch disk from suddenly falling out of place. Make note of the clutch plate installation direction before removing to ensure proper reassembly. Some clutch disks can be installed backwards, however in doing so, will not allow adequate movement of the pressure plate fingers. If installed in this fashion, the clutch will not disengage!
6. Check the clutch driven disc for excessive wear or cracks. If the clutch disk's hub has integral torsional dampening springs, as used with standard one piece flywheels, check the springs for breakage and a tight fit. Replace the disk if the springs are loose, broken, or cracked. Dual mass flywheels use a clutch disk with a solid hub and do not use damper springs, however both types of clutch disks should be inspected for spline wear and the rivets inspected for tightness. Replace the disk if the rivets are loose, if the splines are worn excessively, or if the inner hub shows signs of fatigue, cracking or looseness.

Clutch disk lining wear limit as measured from the head of the rivet to the lining surface:

Minimum thickness: 0.04 inches (1.0mm)

1. Check the flywheel and pressure plate to make sure they are not scored, cracked, or burned, even at a small spot. Use a straight edge and a feeler gauge to make sure the contact surface is true. Replace any defective parts. Signs of bluing on the pressure plate or flywheel are indicators of excessive heat, usually caused by excessive clutch slippage. If bluing has occurred on the pressure plate it must be replaced as the spring's clamping force has been compromised and even with a new clutch disk installed, clutch plate slippage and/or premature failure is likely to occur.

Fig. A pressure plate can be checked for flatness using a precision straight edge and a 0.004 inch (0.10mm) feeler gauge

Fig. A clutch disk alignment tool shown installed through the clutch hub. Note the similarity of the alignment tool and . . .

Fig. . . . the transmission input shaft

Fig. The clutch disk must be installed properly to ensure proper operation. Some disks are stamped on the inner hub to denote the direction of installation

Fig. The clutch disk is checked for wear by measuring the distance from the head of the rivet to the surface lining. The disk should be replaced if the distance is 0.040 inches (1.0mm) or less

Fig. The clutch fork retaining clip shown installed on the fork's pivot with the fork removed

Fig. The clutch release fork is held in place by a small wire retaining clip. The release bearing slides onto the guide tube and into the fork

Fig. The clutch alignment tool shown holding the disk in place with the pressure plate removed

Fig. With the alignment tool installed, torque the fasteners using a crisscross pattern. A click-type torque wrench works well in this application

To install:

NOTE

When replacing the clutch disk, the pressure plate and release bearing should also be replaced. Sometimes these components can be purchased as a clutch kit, with a substantial cost savings.

WARNING

Avoid using rebuilt or resurfaced clutch components on BMW vehicles. The tolerances of these components are critical to their operation and longevity.

1. Clean as necessary and inspect the following items before reassembling the clutch. Replace worn or damaged components as necessary:
   
   
   Clutch lining wear

   Flywheel surface condition

   Rear main/flywheel oil seal

   Transmission input shaft seal

   Clutch pressure plate surface condition

   Flywheel starter ring gear tooth damage

   Clutch fork, check for cracks or excessive wear

   Clutch pilot bearing, check for binding and looseness

   Clutch hub wear, and if used, damper spring condition

   Clutch release bearing, check for binding and looseness

   Clutch pressure plate mounting fasteners, replace on S50 engines

   Dual mass flywheels, inspect the viscous coupling as outlined in this section.
   
   

NOTE

On S50 engines, the pressure plate mounting bolts must be replaced.

WARNING

The clutch pressure plate mounting fasteners must be a matched set otherwise the engine's balance may be upset. If one fastener is damaged or lost, replace all the fasteners as a set. If the flywheel is removed, the flywheel fasteners must be replaced.

NOTE

On S14 engines, the pressure plate mounting bolts and taper sleeve must be replaced.

1. Make sure the friction surfaces of the clutch, flywheel and pressure plate are clean and dry. If the flywheel, or pressure plate are to be replaced, make sure the protective coatings are properly removed as recommended by the manufacturer. Often times these components are packaged and wrapped with an oiled cloth and/or a protective coating to prevent rusting during shipping and storage.
2. Install a clutch alignment tool through the splines of the clutch disk and place the disk against the flywheel, then slide the alignment tool into the pilot bearing to hold the disk in place. Make sure the disk is installed in the correct direction.

WARNING

A clutch alignment tool should be used when assembling the clutch. Proper alignment of the clutch splines and the pilot bearing is critical for the input shaft of the transmission to slide into position without binding or damage.

1. If the flywheel was removed or replaced, make sure it is installed properly, and if equipped, the speed and reference mark sensors are properly installed.

WARNING

If the vehicle is equipped with a flywheel that uses speed and reference sensors, make sure they are properly installed and not damaged, otherwise the engine management system may not function upon reassembly.

1. Install a flywheel locking tool to prevent the flywheel from rotating.
2. Place the pressure plate against the clutch disk and flywheel, making sure the mounting holes are properly aligned.
3. Initially install the fasteners by hand turning them at least four complete revolutions in a crisscross pattern. On S50 engines, the pressure plate mounting bolts must be replaced. On S14 engines, the pressure plate mounting bolts and taper sleeve must be replaced.
4. Continue tightening the fasteners evenly in a crisscross pattern while holding the clutch alignment tool centered. Even with an alignment tool installed, the free-play in the release bearing and the weight of the clutch disk is enough to allow a slight amount of misalignment.
5. Once the fasteners begin to apply tension to the pressure plate, slide the clutch alignment tool in and out to check for excessive drag. If excessive drag is felt the clutch disk is not uniformly aligned and it must be moved slightly until the tool can be removed and installed easily. If necessary, back the clutch pressure plate fasteners off to relieve the tension so the clutch disk can be moved slightly.
6. Torque the fasteners in a crisscross pattern as follows:
   
   
   M8 8.8: 18 ft. lbs. (24 Nm)

   M8 10.9: 25 ft. lbs. (34 Nm)

   S14 M8 10.9: 25 ft. lbs. (34 Nm)
   
   
7. Slide the clutch alignment tool in and out to recheck for excessive drag and correct as necessary.
8. Coat the following with a light coating of an approved high temperature grease.
   
   
   The transmission input shaft splines

   Release bearing-to-fork contact area

   Release fork pivot and slave cylinder actuation rod contact area

   Release bearing interior collar and sliding sleeve (Do not grease these if the collar is plastic, clean only before assembly)
   
   
9. Install the release fork onto the transmission, making sure the retaining clip is properly fastened onto the grooved shaft of pivot ball, and clamped around the release fork.
10. Slide the release bearing onto the guide tube and center it in the release fork.
11. The balance of assembly is in reverse order of removal, noting the following:
12. Keep the mating surfaces of the transmission and engine parallel with one another as the transmission is installed.
13. If necessary, put the transmission in gear and move the output drive flange until the transmission input shaft aligns with the clutch hub.
14. Check and top off all fluid levels as necessary.

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   
   Negative battery cable

   Heat shield, then the mounting bolts

   Speed and reference mark sensors at the flywheel housing. Mark the plugs for reinstallation.

   Transmission and clutch housing

   With a 265/6 transmission (without an integral clutch housing), clutch housing. On vehicles with 6-cylinder engines, a Torx® socket is required.
   
   
3. Prevent the flywheel from turning, using a suitable locking tool.
4. Loosen the mounting bolts one after another gradually, 1-1¹₂
5. Remove the mounting bolts, clutch and driveplate. Coat the splines of the transmission input shaft with Molykote® Long-term 2, Microlube® GL 2611. Be sure the clutch pilot bearing, located in the center of the crankshaft, turns easily.
6. Check the clutch driven disc for excess wear or cracks. Check the integral torsional damping springs, used with lighter flywheels only, for tight fit. Inspect the rivets to be sure they are all tight. Inspect the flywheel to be sure it is not scored, cracked, or burned. Use a straightedge to verify the contact surface is true. Replace any defective parts.







Fig. Clutch pressure plate mounting bolts

To install:

NOTE

On vehicles with 6-cylinder engines, the clutch pressure plate must fit over dowel pins.

1. To install, fit the new clutch disk on a suitable clutch alignment tool and center the tool with the flywheel by centering it with the clutch pilot bearing. Mount the clutch pressure plate and install the mounting bolts. Clutch mounting bolts: 16-19 ft. lbs. (21-26 Nm).
2. When installing the clutch retaining bolts turn them in gradually to evenly tighten the clutch pressure plate to prevent warpage.
3. Install or connect the following:
   
   
   Clutch housing, if equipped with separate housing, then the transmission. If the clutch housing is part of the transmission, install the transmission.

   Speed and reference mark sensors, if equipped; then the heat shield

   The remaining components in the reverse order from which they were removed

   All remaining fluids as necessary

   Negative battery cable
   
   

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   
   
   Negative battery cable

   Heat shield, then the mounting bolts. Disconnect the speed and reference mark sensors at the flywheel housing. Mark the plugs for reinstallation.

   Transmission and clutch housing

   With a 265/6 transmission (without an integral clutch housing), clutch housing. On vehicles with 6-cylinder engines, a Torx® socket is required.
   
   
3. Prevent the flywheel from turning, using a suitable locking tool.
4. Loosen the mounting bolts one after another gradually, 1-1 ¹ / ₂ turns at a time, to relieve tension from the clutch.
5. Remove the mounting bolts, clutch and driveplate. Coat the splines of the transmission input shaft with Molykote® Long-term 2, Microlube® GL 2611. Be sure the clutch pilot bearing, located in the center of the crankshaft, turns easily.
6. Check the clutch driven disc for excess wear or cracks. Check the integral torsional damping springs, used with lighter flywheels only, for tight fit. Inspect the rivets to be sure they are all tight. Inspect the flywheel to be sure it is not scored, cracked, or burned. Use a straightedge to verify the contact surface is true. Replace any defective parts.

To install:

NOTE

On vehicles with 6-cylinder engines, the clutch pressure plate must fit over dowel pins.

1. To install, fit the new clutch disk on a suitable clutch alignment tool and center the tool with the flywheel by centering it with the clutch pilot bearing. Mount the clutch pressure plate and install the mounting bolts. Clutch mounting bolts: 16-19 ft. lbs. (21-26 Nm).
2. When installing the clutch retaining bolts turn them in gradually to evenly tighten the clutch pressure plate to prevent warpage.
3. Install or connect the following:
   
   
   Clutch housing, if equipped with separate housing, then the transmission. If the clutch housing is part of the transmission, install the transmission.

   If equipped, speed and reference mark sensors, then the heat shield

   The remaining components in the reverse order from which they were removed

   All remaining fluids as necessary

   Negative battery cable
   
   

1. Disconnect the negative battery cable. Raise and safely support the vehicle. Remove the heat shield and then the mounting bolts. Disconnect the speed and reference mark sensors at the flywheel housing. Mark the plugs for reinstallation.
2. Remove the transmission and clutch housing.
3. On vehicles with 6-cylinder engines, a Torx® socket is required. If equipped with a 265/6 transmission (without an integral clutch housing), remove the clutch housing.
4. Prevent the flywheel from turning, using a locking tool.
5. Loosen the mounting bolts one after another gradually, 1-1 ¹ / ₂ turns at a time, to relieve tension from the clutch.
6. Remove the mounting bolts, clutch and driveplate. Coat the splines of the transmission input shaft with Molykote® Long-term 2, Microlube® GL 2611 or equivalent. Make sure the clutch pilot bearing, located in the center of the crankshaft, turns easily.
7. Check the clutch driven disc for excess wear or cracks. Check the integral torsional damping springs, used with lighter flywheels only, for tight fit. Inspect the rivets to make sure they are all tight. Check the flywheel to make sure it is not scored, cracked, or burned, even at a small spot. Use a straightedge to make sure the contact surface is true. Replace any defective parts.

To install:

1. To install, fit the new clutch plate and disc in place and install the mounting bolts.
2. When installing the clutch retaining bolts turn them in gradually to evenly tighten the clutch disc and to prevent warpage.
3. Install the transmission and the clutch housing.
4. If equipped, install the speed and reference mark sensors. Install the heat shield.
5. Note that on vehicles with 6-cylinder engines, the clutch pressure plate must fit over dowel pins. Torque the clutch mounting bolts to 16-19 ft. lbs. (21-26 Nm).

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   
   Negative battery cable

   Heat shield, then the mounting bolts

   Speed and reference mark sensors at the flywheel housing. Mark the plugs for reinstallation.

   Transmission and clutch housing

   With a 265/6 transmission (without an integral clutch housing), clutch housing. On vehicles with 6-cylinder engines, a Torx® socket is required.
   
   
3. Prevent the flywheel from turning, using a suitable locking tool.
4. Loosen the mounting bolts one after another gradually, 1-1 ¹ / ₂ turns at a time, to relieve tension from the clutch.
5. Remove the mounting bolts, clutch and driveplate. Coat the splines of the transmission input shaft with Molykote® Long-term 2, Microlube® GL 2611. Be sure the clutch pilot bearing, located in the center of the crankshaft, turns easily.
6. Check the clutch driven disc for excess wear or cracks. Check the integral torsional damping springs, used with lighter flywheels only, for tight fit. Inspect the rivets to be sure they are all tight. Inspect the flywheel to be sure it is not scored, cracked, or burned. Use a straightedge to verify the contact surface is true. Replace any defective parts.
   
   
   

   

   Fig. Clutch pressure plate mounting bolts

To install:

NOTE

On vehicles with 6-cylinder engines, the clutch pressure plate must fit over dowel pins.

1. To install, fit the new clutch disk on a suitable clutch alignment tool and center the tool with the flywheel by centering it with the clutch pilot bearing. Mount the clutch pressure plate and install the mounting bolts. Clutch mounting bolts: 16-19 ft. lbs. (21-26 Nm).
2. When installing the clutch retaining bolts turn them in gradually to evenly tighten the clutch pressure plate to prevent warpage.
3. Install or connect the following:
   
   
   Clutch housing, if equipped with separate housing, then the transmission. If the clutch housing is part of the transmission, install the transmission.

   Speed and reference mark sensors, if equipped; then the heat shield

   The remaining components in the reverse order from which they were removed

   All remaining fluids as necessary

   Negative battery cable
   
   

----------------

For more car related problem troubleshooting:---

This are the sections, you can go through and click the link to read its troubleshooting.

---------

The car will not start?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-start.html

-----------------

Car will not crank?

http://schematicsdiagram.blogspot.com/2011/06/car-will-not-crank.html

-----------

Car has no spark?

http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html

-------------

How to troubleshoot car battery?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-car-battery.html

-----------------

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

car will turn over but will not start?

http://technoanswers.blogspot.com/2011/05/car-will-turn-over-but-will-not-start.html

-----------------

The Brake Indicator Light Stays On dash of car?

http://schematicsdiagram.blogspot.com/2011/06/brake-indicator-light-stays-on-dash-of.html

The ABS and Traction Control Lights stays ON dash of car?

http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

Check Engine Light On car?

http://schematicsdiagram.blogspot.com/2011/06/check-engine-light-on-car.html

-------------------------

How to replace Interior Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-interior-lights-on-car.html

Car lights not working, even after replacing the bulb/lamp?

Click this link below:--

http://schematicsdiagram.blogspot.com/2011/06/car-lights-not-working-even-after.html

---------------

How to replace head lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-head-lights-on-car.html

--------------------

How to replace Parking, turn, and Brake Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-parking-turn-and-brake.html
How to remove the door panel on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-remove-door-panel-on-car.html

How to replace power window motor in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-power-window-motor-in.html

How to test relays on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-relays-on-car.html

-----------------------------

How to troubleshoot Engine Misfires?

http://schematicsdiagram.blogspot.com/2011/06/how-to-troubleshoot-engine-misfires.html

------------

The spark plug firing order for car?

http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html

------------------------

Where is the Thermostat located in car?

http://schematicsdiagram.blogspot.com/2011/06/where-is-thermostat-located-in-car.html

How to recharge AC on Auto/Truck/car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-recharge-ac-on-autotruckcar.html

-------------------

How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

To Order car parts online:--To get heavy discount on car parts .Click this link below:----

http://technoanswers.blogspot.com/2011/05/from-where-to-order-car-parts-online.html

How to Replace Coil Springs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-coil-springs.html

How to Replace an Oil Pan Gasket?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html

How to Replace a Fuel Injector

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-injector.html

How to Replace a C.O.P. Type Ignition Coil?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cop-type-ignition-coil.html

How to Replace a Fuel Pressure Regulator?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pressure-regulator.html

How to Replace a Fuel Pump?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-pump.html

How to Replace a Rear Lift Gate Locking Mechanism?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-lift-gate-locking.html

How to Clean a Fuel System

http://schematicsdiagram.blogspot.com/2011/07/how-to-clean-fuel-system.html

How to Replace an Ignition Coil

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-coil.html

How to Replace a Windshield

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield.html

How to Replace a Mass Air Flow Sensor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mass-air-flow-sensor.html

How to Replace a Rear Distance Sensor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-distance-sensor.html

How to Replace a Muffler

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-muffler.html

How to Replace an Engine

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-engine.html

How to Replace an Intake Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-intake-manifold-gasket.html

How to Replace an Oil Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html

How to Lubricate a Brake Pedal Linkage ?

http://schematicsdiagram.blogspot.com/2011/07/how-to-lubricate-brake-pedal-linkage.html

How to Replace a Windshield Wiper Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-motor.html

How to Replace a Distributor Cap

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-distributor-cap.html

How to Replace a Door Weather Stripping

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-door-weather-stripping.html

How to Replace a Freeze Plug

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-freeze-plug.html

How to Replace a Head Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-head-gasket.html

How to Replace a Heater Core

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-core.html

How to Replace Spark Plugs?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html

How to Replace a Rear Axle Bearing?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-axle-bearing.html

How to Replace a Front Bumper Cover

http://technoanswers.blogspot.com/2011/07/how-to-replace-front-bumper-cover.html

How to Replace a Manual Transmission

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-manual-transmission.html

How to Replace a Headlight Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

How to Replace a Headlight Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

How to Replace Windshield Wiper Blades

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-blades.html

How to Replace a Cooling Fan

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-cooling-fan.html

How to Replace a Catalytic Converter

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-catalytic-converter.html

How to Replace an Engine Mount

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-engine-mount.html

How to Replace a Fog Light Assembly

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fog-light-assembly.html

How to Change Engine Oil and Filter

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html

How to Replace a Power Seat Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-seat-switch.html

How to Replace a Rear Main Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-main-seal.html

How to Repair a Defroster Grid

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-defroster-grid.html

How to Replace an AWD Transfer Case

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-awd-transfer-case.html

How to Replace a Plastic License Plate Bracket?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-plastic-license-plate.html

How to Replace a Power Seat Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-seat-motor.html

How to Replace Power Steering Fluid

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-steering-fluid.html

How to Replace a Power Window Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-window-switch.html

How to Replace a Quarter Glass Panel?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-quarter-glass-panel.html

How to Pressure Test a Radiator and Cap

http://schematicsdiagram.blogspot.com/2011/07/how-to-pressure-test-radiator-and-cap.html

How to Replace a Radiator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-radiator.html

How to Repair a Hood.

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-hood.html

How to Replace an Energy Absorber

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-energy-absorber.html

How to Replace Heater Core Hoses

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-core-hoses.html

How to Replace a Thermostat.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-thermostat.html

How to Rotate Tires.

http://schematicsdiagram.blogspot.com/2011/07/how-to-rotate-tires.html

How to Replace Wheel Lug Nuts

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-wheel-lug-nuts.html

How to Replace a Tire Valve Stem

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-tire-valve-stem.html

How to Change a Flat Tire

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-flat-tire.html

How to Replace Leaf Springs

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-leaf-springs.html

How to Replace a Heater Control Valve

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-heater-control-valve.html

How to Replace Transmission Cooler Lines

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transmission-cooler.html

How to Replace an Ignition Control Unit

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-ignition-control-unit.html

How to Replace a Brake Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-brake-hose.html

How to Replace a Transfer Case Rear Output Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transfer-case-rear.html

How to Replace a Seat Belt and Seatbelt Retractor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-seat-belt-and-seatbelt.html

How to Replace a Power Steering Rack

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-steering-rack.html

How to Bleed Brakes with a Tool

http://schematicsdiagram.blogspot.com/2011/07/how-to-bleed-brakes-with-tool.html

How to Replace a Tail Light Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-tail-light-bulb.html

How to Check Automatic Transmission Fluid Level

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

How to Change Automatic Transmission Fluid and Filter

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

How to Replace Vacuum Hoses

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-vacuum-hoses.html

How to Replace an Air Intake Boot

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-air-intake-boot.html

How to Replace a Valve Cover Gasket

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-valve-cover-gasket.html

How to Replace a Water Pump

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

How to Replace a Windshield Wiper Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-windshield-wiper-switch.html

How to Replace Window Run Channel Seals

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-run-channel-seals.html

How to Replace a Window Regulator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-regulator.html

How to Balance a Tire and Wheel

http://schematicsdiagram.blogspot.com/2011/07/how-to-balance-tire-and-wheel.html

How to Replace a Window Motor

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-motor.html

How to Adjust a Hood Release Latch?

http://schematicsdiagram.blogspot.com/2011/07/how-to-adjust-hood-release-latch.html

How to Replace a Radiator Support

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-radiator-support.html

How to Replace a Rear Pinion Seal.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html

How to Replace Battery Cables

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-battery-cables.html

How to Replace a Proportioning Valve

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-proportioning-valve.html

How to Replace an Upper Radiator Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html

How to Replace a Lower Radiator Hose

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html

How to Replace a Timing Belt?

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-timing-belt.html

How to Check for Loose or Worn Suspension

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-for-loose-or-worn.html

How to Check for Loose Steering System

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-for-loose-steering-system.html

How to Replace an Oil Pressure Switch (Sensor)

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html

How to Replace a Fender Liner or Splash Shield

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fender-liner-or-splash.html

How to Replace a Hood Insulator

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-hood-insulator.html

How to Replace a Rear Differential.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-differential.html

How to Repair a Hood Hinge

http://schematicsdiagram.blogspot.com/2011/07/how-to-repair-hood-hinge.html

How to Replace a Brake Pedal Return Spring

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-brake-pedal-return.html

How to Replace a Door Shell.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-door-shell.html

How to Replace a Transfer Case Front Output Seal

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-transfer-case-front.html

How to Replace a Hood Latch/Lock Assembly

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-hood-latchlock-assembly.html

How to Replace a Lift Gate Strut

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lift-gate-strut.html

How to Replace Mud Flaps (Mud Guards)

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mud-flaps.html

How to Check Differential Oil Leaks and Replace Oil.

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html

How to Replace a Mirror

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-mirror.html

How to Replace a Transfer Case Shift Linkage

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transfer-case-shift.html

How to Replace a Transmission Mount

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-transmission-mount.html

How to Replace a U-Joint

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-u-joint.html

How to Replace a Washer Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-washer-tank.html

How to Replace an A/C Line or Hose

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ac-line-or-hose.html

How to Replace a Heater and A/C Blower Motor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-heater-and-ac-blower.html

How to Replace an ABS Control Unit

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-abs-control-unit.html

How to Perform a Brake Adjustment

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-brake-adjustment.html

How to Replace an Alternator Belt

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-alternator-belt.html

How to Replace an Emblem

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-emblem.html

How to Replace an Exhaust Manifold Gasket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-manifold-gasket.html

How to Replace a Tail Pipe

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-pipe.html

How to Replace Shock Absorbers

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-shock-absorbers.html

How to Replace a Strut Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-strut-assembly.html

How to Replace a Driveshaft

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-driveshaft.html

How to Replace a Wheel Cylinder

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-wheel-cylinder.html

How to Replace a Hood

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-hood.html

How to Replace a Brake Disc (Rotor)

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-brake-disc-rotor.html

How to Replace a Metal License Plate Bracket

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-metal-license-plate.html

How to Replace a Power Steering Pump

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-power-steering-pump.html

How to Perform a Basic Engine Tune-Up

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up.html

How to Perform a Basic Engine Tune Up-Oil Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

How to Perform a Basic Engine Tune Up-Spark Plug and Wire Change

http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up_01.html

How to Replace a Distributor Cap and Rotor ?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-distributor-cap-and.html

How to Repair a Valance

http://schematicsdiagram.blogspot.com/2011/08/how-to-repair-valance.html

How to Replace a Turn Signal Switch

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-turn-signal-switch.html

How to Replace a Plastic Bumper Cover

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-plastic-bumper-cover.html

How to Replace a Parking Brake Cable

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-parking-brake-cable.html

How to Replace Windshield Wiper Blade Refills

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-windshield-wiper-blade.html

How to Replace a Corner Light

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-corner-light.html

How to Replace a Bumper Bracket or Side Support

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-bumper-bracket-or-side.html

How to Replace a Washer Pump.

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-washer-pump.html

How to Replace a Grille

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-grille.html

How to Replace a Locking Hub

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-locking-hub.html

How to Replace a Fender

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fender.html

How to Replace a Power Steering Hose

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-power-steering-hose.html

How to Replace a Tailgate

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tailgate.html

How to Replace a Soft Top

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-soft-top.html

How to Replace a Carburetor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-carburetor.html

­

How to Replace a Bumper Trim

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-bumper-trim.html

How to Replace Trunk Strut

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-trunk-strut.html

How to Replace a Front End Cover

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-end-cover.html

How to Replace a Front Pipe

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-pipe.html

How to Replace an Antenna Mast

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-antenna-mast.html

How to Replace a Side Marker Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-side-marker-light.html

How to Install a Carpet on car?

http://schematicsdiagram.blogspot.com/2011/08/how-to-install-carpet-on-car.html

How to Replace a Spoiler

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-spoiler.html

How to Replace a Mirror Glass on car?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-mirror-glass-on-car.html

How to Replace a Step Bumper?

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-step-bumper.html

How to Replace a Door Lock

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-door-lock.html

How to Replace a Throttle Body

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-throttle-body.html

How to Replace a Throttle Position Sensor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-throttle-position-sensor.html

How to Replace a Grille Insert

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-grille-insert.html

How to Replace a Fan Shroud Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fan-shroud-assembly.html

How to Replace an Engine Splash Shield

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-engine-splash-shield.html

How to Replace a Turn Signal Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-turn-signal-light.html

How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html

How to Replace a Park Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

How to Replace an Expansion Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-expansion-tank.html

How to Replace an Exhaust System

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-exhaust-system.html

How to Replace a Fender Trim

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fender-trim.html

How to Replace a Headlight Door

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

How to Replace a Fan Shroud

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fan-shroud.html

How to Replace a Harmonic Balancer

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-harmonic-balancer.html

How to Replace a Header Panel

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-header-panel.html

How to Replace a Fuel Tank

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank.html

How to Replace a Fuel Tank Cap

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-tank-cap.html

How to Replace a Distributor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-distributor.html

How to Replace an EGR Valve

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-egr-valve.html

How to Replace an Oxygen Sensor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-oxygen-sensor.html

How to Replace an Ignition Wire Set

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-ignition-wire-set.html

How to Replace a Tail Light

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-light.html

How to Replace a Door Handle

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-door-handle_18.html

How to Replace a Hood Strut

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-hood-strut.html

How to Replace Tail Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tail-light-assembly.html

How to Replace a Front Bumper

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-front-bumper.html

How to Replace a Fuel Pump Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-fuel-pump-assembly.html

How to Replace an Axle Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-axle-assembly.html

How to Replace a Tailgate Handle

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-tailgate-handle.html

How to Replace a Wheel Hub Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-wheel-hub-assembly.html

How to Replace a Control Arm

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-control-arm.html

How to Replace a Window Regulator with Motor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-window-regulator-with.html

How to Replace a Headlight

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

How to Check the Brake Fluid Level

http://schematicsdiagram.blogspot.com/2011/08/how-to-check-brake-fluid-level.html

How to Replace a Parking Brake Switch

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-parking-brake-switch.html

How to Replace a Blower Motor Resistor

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-blower-motor-resistor.html

How to replace frost plug on car?

http://howtobyme.blogspot.com/2011/08/how-to-replace-frost-plug-on-car.html

Horn stopped working?

http://howtobyme.blogspot.com/2011/08/horn-stopped-working.html

How to clean egr valve on Isuzu Amigo?

http://howtobyme.blogspot.com/2011/08/how-to-clean-egr-valve-on-isuzu-amigo.html

Cruise control stopped working?

http://howtobyme.blogspot.com/2011/08/cruise-control-stopped-working.html

Car is stuck in park and the shift will not move?

http://howtobyme.blogspot.com/2011/08/car-is-stuck-in-park-and-shift-will-not.html

How to change the outer door weather strip?

http://howtobyme.blogspot.com/2011/08/how-to-change-outer-door-weather-strip.html

Car slows down when it gets hotter?

http://howtobyme.blogspot.com/2011/08/car-slows-down-when-it-gets-hotter.html

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.html

Car won't rev past 1900 rpms?

http://howtobyme.blogspot.com/2011/08/car-wont-rev-past-1900-rpms.html